Netgear Nighthawk Router Keeps Rebooting

Netgear Nighthawk Router Keeps Rebooting: What should I Do?

‘Ah! My Nighthawk router is constantly resetting itself. – Does something like that ring a bell? It is the issue that has recently been cited most frequently by Netgear customers. If restarting has also become an issue with your Netgear Nighthawk router, you have arrived at the appropriate location. In this section, you will find a variety of approaches that can help you overcome the problem NetGear nighthawk keeps rebooting that you are presently struggling with within a matter of minutes. So, let’s get started.

The Netgear Router Keeps Rebooting, and a Problem That Has Been Fixed

Solution 1:

Your Netgear router doesn’t need to be operational twenty-four hours each day and seven days a week, even though it is an excellent technology. Your Netgear router may be overworking and requiring you to reboot it manually regularly. Your router’s processor will eventually become overloaded if you continue to work too hard. Therefore, the first step you can take to fix the issue is to make sure that your router is turned off whenever it is not being used. It would help if you also thought about removing any unnecessary CPU baggage from your Nighthawk router.

Reduce the amount of WiFi client devices connected to your Netgear router’s network. You can also do this to prevent the router from working too hard.

Solution 2:

Your Netgear Nighthawk router, just like most other pieces of technological equipment, runs on software that is built right into it. This piece of software is referred to as the firmware of the Netgear router. There is a good chance that the firmware on your Netgear router needs to be updated, which is the likely cause of its ongoing need to reboot. Have no fear! Installing the latest firmware from Netgear is something you should do before your WiFi device entirely freezes.

Accessing the Netgear Router login page for a Netgear router allows for a straightforward firmware upgrade to be performed on a Nighthawk router. The Firmware Update option can be found under the Settings menu on the Netgear Genie setup wizard. All that is required of you is to seek it. Your Nighthawk router can be brought up to date by selecting the option to Update the Firmware, and if the NetGear router keeps rebooting problem will be solved.

Solution 3:

Is the amount of electricity that your Netgear Nighthawk router is receiving sufficient? It would appear that the damaged wall socket is to blame for your run of poor luck. Therefore, do not waste time and immediately put your Netgear router into a different wall socket.

After you have finished, turn on your Netgear Nighthawk router and check to see if it is still experiencing the issue of constantly rebooting. If you answered yes, proceed to the next possible solution.

Solution 4:

If none of the aforementioned alternatives seem to be helping, then the problem may have been caused by the router in question becoming too hot. If you keep your router in a confined space, it runs the risk of overheating. Consequently, you should think about moving your router to a room with adequate ventilation and making a move as soon as possible.

Even if you have already positioned your router in a ventilated area, there is still a good probability that dust has formed on top of it, causing it to overheat. Now would be a good time to clean your Netgear router, wouldn’t it? Check to see if your router is operating normally when you are finished.

Solution 5:

If the Ethernet cable that is connecting your Netgear router and modem is damaged, then you have discovered an additional factor that has led you to the problem that you are presently encountering. So, tell me, what exactly are you anticipating? You should replace the Ethernet cable you’re using to connect your WiFi device with a new one.

In addition, check to be that the Ethernet wire is attached securely to the appropriate ports on each of your WiFi devices.

Solution 6:

Have you tried any of these hacks, and did none of them work for you? Regrettably, you will need a factory reset on your Netgear Nighthawk router. When you perform a factory default reset on your router, it will return to its initial configuration settings. However, the good news is that you won’t have to worry about your Nighthawk router needing to reset all the time.

Find the button labeled “Reset,” and then use something pointed to press it to return your Nighthawk router to the settings it had when it was first manufactured. Your device will perform a factory reset once you let go of the button. Installing your router can then be accomplished by logging into the Netgear Nighthawk setup wizard.

Closing Remarks

However, if rebooting itself presents a challenge, we have included an overview of the different workarounds that may be used in its place. Netgear modem router keeps rebooting has proven to be one of the most successful strategies for fixing a wide variety of problems that are associated with routers. We have high hopes that the workarounds given above will assist you in solving the problem. If the answer is affirmative, connect your client devices to the network of the extender using the WPS technique, and then check to see if the wps light on the router is lit up in the green color. Congratulations! You should now be able to utilize the internet on any client device, as your Nighthawk router has been restored to its usual operating status.

Sanchit Kaushal is the Co-Founder of Network Solution, a content creation company. He’s been a content marketer for over 5 years and writes for Tech, Entrepreneur, Inc and many other blogging and publications website strategy.